Jamil Ikhmayies / Li / Carpenter Characterization of Minerals, Metals, and Materials 2016

1. Auflage 2016
ISBN: 978-3-319-48210-1
Verlag: Springer International Publishing
Format: PDF
Kopierschutz: 1 - PDF Watermark

E-Book, Englisch, 788 Seiten, Web PDF

Reihe: Chemistry and Materials Science

Characterization is an important and fundamental step in material research before and after processing. This bookfocuses on the characterization of minerals, metals, and materials as well as the application of characterization results on the processing of these materials. It is a highly authoritative collection of articles written by experts from around the world. The articles center on materials characterization, extraction, processing, corrosion, welding, solidification, and method development. In addition, articles focus on clays, ceramics, composites, ferrous metals, non-ferrous metals, minerals, electronic, magnetic, environmental, advanced and soft materials. This book will serve the dual purpose of furnishing a broad introduction of the field to novices while simultaneously serving to keep subject matter experts up-to-date.

Zielgruppe

Professional/practitioner

Autoren/Hrsg.

Jamil Ikhmayies, Shadia

Li, Bowen

Carpenter, John

Hwang, Jiann-Yang

Neves Monteiro, Sergio

Li, Jian

Firrao, Donato

Zhang, Mingming

Peng, Zhiwei

Pablo Escobedo-Diaz, J.

Bai, Chengguang

Inhaltsverzeichnis

1;Cover;1
2;Title Page;4
3;Copyright Page;5
4;Preface;18
5;Editors;20
6;Session Chairs;27
7;Table of Contents;6
8;Non-Ferrous;28
8.1;Effect of Microstructural Anisotropy on the Dynamic Mechanical Behaviour of Rolled Ti-6Al-4V;29
8.2;Microstructure Evolution during Thermal Aging of Inconel 718;37
8.3;Microstructure Characterization of Nickel Alloy 718 with Automated Optical Image Processing;45
8.4;An Empirical Equation to Predict the Porosity of Titanium Foams;52
8.5;Microstructure of Metal Injection Molded MIM418 Using Master Alloy Technique;60
9;Method Development;67
9.1;Effect of Poisson’s Ratio on Stress/Strain Concentration at Circular Holes in Elastic Plates Subjected to Biaxial Loading - Three Dimensional Finite Element Analysis;68
9.2;Methodology for Determining Spall Damage Mode Preference in Shocked FCC Polycrystalline Metals from 3D X-Ray Tomography Data;79
10;Minerals;87
10.1;Mineralogical Analysis of Nickel/Copper Polymetallic Sulfide Ore by X-Ray Diffraction Using Rietveld Method;88
10.2;Study on Coal Minerals Phase Transformations Under Different Coking Conditions;96
10.3;Electrical Effect and Influence Factors of Tourmaline;104
10.4;Wettability of Pyrolytic Graphite by Molten Blast Furnace Slag Bearing TiO?;112
10.5;Removing Silica and Alumina from Limonite Using Wet High Gradient Magnetic Separator;120
10.6;Evaluation of White Bentonite Modified by Acid Attack;128
11;Processing and Corrosion;136
11.1;Characterization of Iron Oxide Scale Formed in Naphthenic Acid Corrosion;137
11.2;Effect of Cold Work on the Corrosion Resistance of an Austenitic Stainless Steel;146
11.3;Pyrolysis of Active Fraction of Humic Substances-Based Binder for Iron Ore Pelletizing;153
11.4;Ferronickel Preparation from Nickeliferous Laterite by Rotary Kiln-Electric Furnace Process;161
11.5;Characterization of Copper-Manganese-Aluminum-Magnesium Mixed Oxyhydroxide and Oxide Catalysts for Redox Reactions;169
12;Ferrous;177
12.1;Discussion on Coking Wastewater Treatment and Control Measures in Iron and Steel Enterprises;178
12.2;Effect of MgO and Basicity on Microstructure and Metallurgical Properties of Iron Ore Sinter;183
12.3;Material Characterization of Power Plant Steel in the Virgin and Artificially-Aged Conditions;191
12.4;Site-Specific Studies on the Interfacial Structures of Galvanized Dual Phase Steels;199
12.5;Metallurgy and Creep Behavior of Type 310S Stainless Steel at High Temperature in Different Atmospheres and Loading Conditions;209
12.6;Characterization of Humic Acid Modified Bentonite Binder for Iron Ore Pelletization;217
12.7;Optimization of Material Properties of High Strength Multiphase Steels via Microstructure and Phase Transformation Adjustment;225
13;Clays & Ceramics;233
13.1;Formulation of Ceramic Body to Produce Roofing Tiles Using Winkler Diagram;234
13.2;FTIR Spectroscopy of Some Brazilian Clays;241
13.3;Preparation and Characterization of Microcapsules from PBSL/VMF2 Nanocomposite;249
13.4;Thermal Properties of Polypropylene Nanocomposites with Organoclay and Discarded Bond Paper;254
13.5;Incorporation of Waste Ceramic Blocks in Structural Ceramics;262
13.6;Solidification of Dredged Sludge by Hydraulic Ash-Slag Cementitious Materials;267
13.7;Synthesis and Characteristics of Anorthite Ceramics from Steelmaking Slag;274
14;Composites;281
14.1;Tensile Strength Tests in Epoxy Composites with High Incorporation of Malva Fibers;282
14.2;Microstructural Characteristics of Reaction-Bonded Microstructural Characteristics of Reaction-Bonded B?C/SiC Composite;287
14.3;Analysis of Methanol Sensitivity on SnO?-ZnO Nanocomposite;295
15;Extraction;300
15.1;Experimental Study on Quality Evaluation of Calcium-Based Agents for Desulfurization of Sinter Gas on SDA;301
15.2;Kinetic Studies for the Absorption of Organic Matter from Purified Solution of Zinc by Coconut Shell Activated Carbon;308
15.3;Recovery of Palladium from Spent Pd/Al?O? Catalyst by Hydrochloric Acid Leaching;316
15.4;Prevention of Airborne Dust from Petroleum Coke Stockpiles;324
15.5;Ligand Selection Model for Leaching of Low Grade Zinc Oxide Ores;331
15.6;Studies on Leaching of Oxidized Copper Ore from South America;340
15.7;Effect of Ferric Ions on Bioleaching of Pentlandite Concentrate;348
15.8;Characterization and Stoichiometry of the Cyanidation Reaction in NaOH of Argentian Waste Tailings of Pachuca, Hidalgo, México;357
16;Soft Materials;365
16.1;Tensile Strength of Polyester Composites Reinforced with Thinner Ramie Fibers;366
16.2;Charpy Impact Tests of Polyester Composites Reinforced with PALF Fibers;372
16.3;Dynamic-Mechanical Characterization of Polyester Matrix Composites Reinforced with Eucalyptus Fibers;378
16.4;Flexural Mechanical Characterization of Polyester Composites Reinforced with Ramie Fibers;385
16.5;Tensile Strength of Epoxy Composites Reinforced with Fique Fibers;391
16.6;Thermal Analysis of Curaua Fiber Reinforced Epoxy Matrix Composites;397
16.7;Characterization of Thermal Behavior of Epoxy Composites Reinforced with Curaua Fibers by Differential Scanning Calorimetry;403
16.8;Comparative Study of the Effects of Cellulose Nanowhiskers and Microcrystalline Cellulose Addition as Reinforcement in Flexible Films Based on Biopolymer Blends;408
16.9;Flexural Test in Epoxy Matrix Composites Reinforced with Hemp Fiber;416
17;Electronic, Magnetic, Environmental, and Advanced Materials;423
17.1;The Influence of Heat Treatment on the Optical Parameters of Spray-Deposited CdS:In Thin Films;424
17.2;Determination of the Stability Constants of Mixed-Ligand Coordination Compounds in the Zn(II)-Nitrilotriacetic Acid-Ammonia System;432
17.3;Resonanaces of Microwave Power Absorption in Alumina and Silicon Carbide;440
17.4;Physical and Chemical Properties of MSWI Fly Ash;447
18;Welding and Solidification;456
18.1;Influence of Al and C on Mechanical Properties of Sub-Rapidly Solidified Fe–20Mn–xAl–yC Low-Density Steels;457
18.2;Dynamic Deep Etching and Particle Extraction for High-Strength Aluminum Alloys;463
18.3;Optimization of TiNp/Ti Content for Si?N?/42CrMo Joints Brazed with Ag-Cu-Ti+TiNp Composite Filler;469
19;Poster Session;477
19.1;Tribological Testing, Analysis and Characterization of D.C. Magnetron Sputtered Ti-Nb-N Thin Film Coatings on Stainless Steel;478
19.2;Assimilation Reaction Characteristic Number for Evaluating the Assimilation of Iron Ore in Sintering;486
19.3;Experimental Study of Advanced Treatment of Coking Wastewater Using MBR-RO Combined Process;494
19.4;Small Punch Creep Test in a 316 Austenitic Stainless Steel;500
19.5;Effect of Phase Transformations on Hardness in Zn-Al-Cu Alloys;508
19.6;Recovery of Palladium and Aluminum from Spent Catalysts by Roasting-Leaching;515
19.7;Preparation of Polymeric Phosphate Ferric Sulfate Flocculant and Application on Coking Wastewater Treatment;523
19.8;Characterization of Incorporation the Glass Waste in Adhesive Mortar;531
19.9;Characterization of a Mineral of the District of Zimapan, Mina Concordia, Hidalgo, for the Viability of the Recovery of Tungsten;538
19.10;Mechanical Properties and Microstructure of K418 Using Master Alloy Technique and Mechanical Alloy;546
19.11;Passive Films Formed on Stainless Steels in Phosphate Buffer Solution;553
19.12;Effect of the Paper Industry Residue on Properties in the Fresh Mortar;561
19.13;Brillouin Scattering Spectroscopy on Mg-Nd Alloy in Different Aging Time;567
19.14;The Characterization of the Desulfurization Powder in the Semi-Dry De-SO? Process of the Sintering Plant Exhaust Gas and Its Interaction with the Soil Particles;575
19.15;Direct Synthesis of Carbon Nanotubes at Low Temperature by the Reaction of CCl? and Ferrocene;583
19.16;Effect of Magnesium Aluminate Spinel Content on Properties of BN Based Composites;589
19.17;Silver Cementation with Zinc from Residual X Ray Fixer, Experimental and Thermochemical Study;595
19.18;Characterization of Waste Molding Sands, for Their Possible Use as Building Material;604
19.19;Improvement of Mechanical Properties in Natural Rubber with Organic Fillers;611
19.20;Speciation and Characterization of E-Waste, Using Analytical Techniques;616
19.21;Development of Bio-Based Foams Prepared from PBAT/PLA Reinforced with Bio-Calcium Carbonate Compatibilized by Electron-Beam Radiation;624
19.22;Microstructure Analysis of Buildups Embedded in Carbon Sleeve in Continuous Annealing Furnace for Non-Oriented Silicon Steel;632
19.23;Properties of Clay for Ceramics with Rock Waste for Production Structural Block by Pressing and Firing;639
19.24;Properties of Mortars with Partial and Total Replacement of Conventional Aggregate by Waste Construction;646
19.25;Effects of Graphene Oxide Addition on Mechanical and Thermal Properties of EVOH Films;652
19.26;Evaluation of Physico-Chemical Properties When Adding Boiler Ashes to Mortar;660
19.27;Significance of Graphitic Surfaces in Aurodicyanide Adsorption by Activated Carbon: Experimental and Computational Approach;667
19.28;Clinker Production from Wastes of Cellulose and Granite Industries;675
19.29;Effects of Carbon Black Incorporation on Morphological, Mechanical and Thermal Properties of Biodegradable Films;681
19.30;Influence of Inoculation on Structure of Chromium Cast Iron;689
19.31;Characterization of Irradiated and Non-Irradiated Rubber from Automotive Scrap Tires;697
19.32;Properties of Ceramic Pigment Zn?.?Cu?.?Cr?O? Synthesized by Solution Combustion Method;705
19.33;Evaluation of Environmental Aging of Polypropylene Irradiated Versus Pristine;712
19.34;Interface Reaction between Y?O? Doped BaZrO? and TiNi Melt;720
19.35;Hydration Resistance of Y?O? Doped CaO and Its Application to Melting Titanium Alloys;728
19.36;Shear Displacement and Actual Strain during Chip Segmentation when Cutting Aerospace Alloy Ti-5553;736
19.37;Surface Behavior of Iron Sulfide Ore during Grinding with Alumina Media;744
19.38;Zinc Chloride Influence on the Resins Furan Polymerization to Foundry Moulds;753
19.39;Characterization of Gamma-Alumina Obtained from Aged Pseudoboehmites;761
19.40;Microstructure, Mechanical and Oxidation Behavior of Niobium Modified 9% Chromium Steel;768
20;Author Index;777
21;Subject Index;783

Über Autor(innen)

The Minerals, Metals & Materials Society (TMS) is a member-driven international professional society dedicated to fostering the exchange of learning and ideas across the entire range of materials science and engineering, from minerals processing and primary metals production, to basic research and the advanced applications of materials. Included among its nearly 13,000 professional and student members are metallurgical and materials engineers, scientists, researchers, educators, and administrators from more than 70 countries on six continents. For more information on TMS, visit www.tms.org.