Watari / Yahaya | 6th Int. Conf. on Advances in Materials, Mechanical and Manufacturing & 13th Int. Conf. on Engineering and Innovative Materials | E-Book | www.sack.de
E-Book

E-Book, Englisch, 116 Seiten

Watari / Yahaya 6th Int. Conf. on Advances in Materials, Mechanical and Manufacturing & 13th Int. Conf. on Engineering and Innovative Materials


Erscheinungsjahr 2025
ISBN: 978-3-0364-1849-0
Verlag: Trans Tech Publications
Format: PDF
 Kopierschutz: 0 - No protection

E-Book, Englisch, 116 Seiten

ISBN: 978-3-0364-1849-0
Verlag: Trans Tech Publications
Format: PDF
 Kopierschutz: 0 - No protection

This edition comprises articles presented at the 6th International Conference on Advances in Materials, Mechanical and Manufacturing (AMMM 2024) and the 13th International Conference on Engineering and Innovative Materials (ICEIM 2024), which were held from 6-8 September 2024 in Tokyo, Japan. The included articles represent the latest research results in additive manufacturing and engineering practice in the development and design of machines, including computational mechanics methods.

Watari / Yahaya 6th Int. Conf. on Advances in Materials, Mechanical and Manufacturing & 13th Int. Conf. on Engineering and Innovative Materials jetzt bestellen!

Autoren/Hrsg.

Watari, Hisaki
Yahaya, Muhammad

Fachgebiete

Weitere Infos & Material

Preface and Committee
Chapter 1: Additive Manufacturing
Optimization of Infill Parameters for Fused Filament Fabrication (FFF) of Polyether Ether Ketone (PEEK) Using Adaptive Neuro-Fuzzy Inference System (ANFIS)
Peanut Hull as an Alternative Biocomposite for Polylactic Acid Filament in Fused Filament Fabrication 3D Printing
Effect of Rigid Body Motion in Phase Field Simulation of Sintering during Preheating at the Powder Bed Fusion with Electron Beam Conditions
Chapter 2: Machines Research and Design
Development of Small Punch Creep Test Rig, Testing and Validation
Trial Production of Disk Caster for Thin Bar
Melt Drag Twin Roll Caster
Design and Properties Analysis of Coating Removal Actuator by Abrasive Water Jet
Exhaust Emission Analysis of Spark Ignition Engine with Modification of Exhaust Gas Recirculation (EGR), Air Intake Tank, and Swirl Generator
Chapter 3: Computational Mechanics
Turbulent Flow Analysis in an Annular Diffuser Having a Rectangular Twisted Hub
Dynamic Response of a Tube of Heat Exchanger with an Axial Load
Numerical Considerations on Design Parameters of Diffuser Vane Slit
Investigation of Stress and Delamination Behaviors of a Bonded Beam Having Orthotropic Inclusion in Adhesive Layer under Tensile Loading
Modal Analysis of Flax Fiber Reinforced Composite Bridge Using FEA to Support the Design of the Target Bridge Made of Innovative Material

Ihre Fragen, Wünsche oder Anmerkungen
Vorname*
Nachname*
Ihre E-Mail-Adresse*
Kundennr.
Ihre Nachricht*
Lediglich mit * gekennzeichnete Felder sind Pflichtfelder.
Wenn Sie die im Kontaktformular eingegebenen Daten durch Klick auf den nachfolgenden Button übersenden, erklären Sie sich damit einverstanden, dass wir Ihr Angaben für die Beantwortung Ihrer Anfrage verwenden. Selbstverständlich werden Ihre Daten vertraulich behandelt und nicht an Dritte weitergegeben. Sie können der Verwendung Ihrer Daten jederzeit widersprechen. Das Datenhandling bei Sack Fachmedien erklären wir Ihnen in unserer Datenschutzerklärung.