Kang / Kobayashi Designing, Processing and Properties of Advanced Engineering Materials

Erscheinungsjahr 2004
ISBN: 978-3-0357-0625-3
Verlag: Trans Tech Publications
Format: PDF
Kopierschutz: 0 - No protection

E-Book, Englisch, 1380 Seiten

Volume is indexed by Thomson Reuters CPCI-S (WoS).Following on the success of the last previous two symposiums, the aim of ISAEM-2003 is was to provide an interactive forum for discussion of the designing, processing and properties of advanced engineering materials of involving metals, ceramics and polymers.

Autoren/Hrsg.

Kang, Sung Goon

Kobayashi, T.

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Committees
Asymmetric Rolling as Means of Texture and Ridging Control and Grain Refinement of Aluminum Alloy and Steel Sheets
High Performance Materials Development in the 21st Century: Trends and Directions
Toughness Assessment of a Variety of Materials: Similarities and Discrepancies
Modeling Precipitate Microstructure Evolution in Alloys with First-Principles Energetic Information
Processing and Alloy Development to Optimise the Properties and Cost-Effectiveness of Components Manufactured from TiAl-Based Alloys
Orientation Dependence of Dynamic Recrystallization Behavior of Al Single Crystals
Recent Progress in Molecular Orbital Approach to Alloy Design
Aerosol Deposition Method for Fabrication of Nano Crystal Ceramic Layer
Quantitative Analysis of Precipitation Behavior in Ferrite of V Added Microalloyed Steel
Characterization of Friction Welding for IN713LC and AISI 4140 Steel
High Temperature Deformation Mechanism Maps of NiAl
Metastable Two-Phase Field(A2+B2) in Co-Al-Fe and Co-Al Alloy Systems
Fabrication of Magnesium Alloy (AZ31) Sheet by Extrusion
Development of Modified Embedded Atom Method for Alkali Metals
Design and Fabrication of Bi-Convex Variable Focusing Lens Arrays Using Liquid Crystal for Integral Photography
Characteristics of Electron Density Distributions in Metal Oxides
High Temperature Wear Properties of Multiphase Composite: The Role of Transfer Film
Properties Evaluation of Composites Including Cracked Ellipsoidal Inhomogeneity
Molecular Dynamics Simulation of Stress Induced Grain Boundary Migration during Nanoindentation Experiments
Influence of Biaxial Surface Stress on Mechanical Indenting Deformations
Molecular Dynamics Analysis of Structure and Intrinsic Stress in Amorphous Silicon Carbide Film with Deposition Process Parameters
Numerical Analysis on the Dissimilar Channel Angular Pressing by Multi-Pass Rolling
A Study on the Process Design of Cold-Forged Automobile Parts
Finite Element Method in Powdered Metal Compaction Processes
Modification of the Recrystallization Texture by Means of Cross Rolling in Ferritic Stainless Steel Sheets
Creep Analysis of Cr-Mo Steels Using a Dislocation Based Constitutive Modelling
Effects of Processing Variables on the Development of the Cube Texture in Ni Tapes Fabricated by the Cold Working of Ni Powder Compact Rods
A New Control Algorithm for Impressed Current Cathodic Protection on the Underwater Hull
Study of Magnetic Annealing on Magnetostriction in Grain-Oriented 3.2 % Si Steels
Effect of Heating Rate on Transient Liquid Phase Diffusion Bonding of Ni-Based Superalloy GTD-111
Notch Effects on Impact Tensile Properties in A6061-T6 Aluminum Alloy
Ultrafine Grained Bulk 5083 Al Alloy Produced by Cryogenic Rolling Process
Aluminum Alloy Strips Casting Using an Unequal Diameter Twin Roll Caster
Development of Light-Weight Al Scroll Compressor for Car Air Conditioner
Effect of Bubbling on the Primary Silicon in Hypereutectic Al-Si Alloy
Effect of Electromagnetic Force on the Silicon Size in Hypoeutectic Al-Si Alloy
Effect of Stacking Layer Number on Mechanical Properties of Accumulative Roll Bonding Processed Aluminum
Enhanced Modification Process of B.390 Casting Alloy by the Ca Content Control
Microstructure Characterizations of Hypereutectic Al-Si Alloys with Different Undercooling Levels
Effect of Distribution Coefficient on Copper Purification by Zone Refining Process
Grain Refinement of Copper Alloys by Equal Channel Angular Pressing
Formability of Magnesium Alloy Sheets Manufactured by Semi-Solid Roll Strip Casting
Transformation Behavior of a Ti-Ni-Cu-Fe Alloy
Prediction of Microstructure During High Temperature Forming of Ti-6Al-4V Alloy
Dissimilar Joining of Nickel Aluminide Intermetallic Compound with Spheroidal Graphite Cast Iron by Using Combustion Synthesis
Surface Amorphization in Intermetallic Compounds by Shot Peening
Combustion Synthesis Process of Ag Added Al3Ti Intermetallic Compound
Morphology of Carbon Micro-Coils
Synthesis of Porous Mullite by Vapor Phase Reaction
Self-Propagating High-Temperature Synthesis of Aluminum Nitride and its Characterization
Fabrication of Activated Carbon Fibers from Stabilized PAN-Based Fibers by KOH
Role of Unstable Chemical Species (Non-Graphitic Carbon and Flowing NH3 Gas) on the Equilibrium Point of the Reaction Product (Carbide, Carbo-Nitride or Nitride)
Sinter-Bonding of Polycrystalline Silicon-Nitride Using Source Powder of Superplastic Ceramics as Insert Material
Processing Technique for Wear Resistance Parts Using Ultra Fine Particles Reinforced Si3N4
Preparation and Characterization of Porous Si-Coated SiC Fiber Media
Abnormal Crystal Growth in the Sintered (Bi0.2Sb0.8)2Te3 Alloys Induced by Silver Addition
Efflorescence and Leaching Behavior of Metal Ions for EAF Dust-Clay Based Bricks
Production Mechanism of Superfine Powders by Jet Mill
Synthesis and Evaluations of Microstructure Properties on Al-(50, 60, 70 mass%)Si Systems by Mechanical Alloying
Nanocomposite Formation in the Fe2O3-M (M=Al, Ti, Zn, Cu) Systems by Mechanical Alloying
Mechanical Alloying Effect of Hematite and Graphite
Sintering Distortion of Barrier Ribs Formed via Capillary Molding
Effect of CoO Doping on the Sintering Ability and Mechanical Properties of Y-TZP
Serration Phenomenon in High Purity Chromium
Synthesis of CuInSe2 and CuInGaSe2 Nanoparticles by Solvothermal Route
Recovery of Lithium from Seawater Using Nano-Manganese Oxide Adsorbents Prepared by Gel Process
Resistance Sintering of Copper-Graphite Powder Mixture under Pressure
Fabrication of Thin Film Using Nanosized Indium Tin Oxide (ITO) Powder and Its Degradation Characteristics
Photocatalysis for Oxidation of Phenol and Reduction of Inorganic Pollutants by Nanocrystalline TiO2-ZrO2 Powders
Fabrication of Al2O3-ZrO2 (3Y-TZP) Composites with Graded Structures by Centrifugal Slip Casting Method
Fabrication and Properties of TiB2 Reinforced Cu Composites by Electromagnetic Stirring
Fabrication of BN/Al(-Mg) Metal Matrix Composite (MMC) by Pressureless Infiltration Technique
Tensile Properties and Fracture Behavior of SiCp/AC4CH Composite at Loading Velocities of up to 10m/s
Preparation of W-C-B Composites by Reactive Resistance-Heated Hot Pressing
Measurement and Analysis of Plasma Arc Cutting Acoustic Signal
Fabrication of Copper Clad Aluminum Wire (CCAW) by Indirect Extrusion and Drawing
Microstructural Effects of Electromagnetic Stirring Strength and Casting Speed in Continuous Casting of Al Alloy
Barrier Ribs of PDP by Injection Molding
Analysis of Waste Heat Recovery to Steel Scrap Preheating in an Enclosure Vessel
Up-Grade Recycle by Consolidating Aluminum Cutting Chip under Severe Plastic Deformation
Low-Cycle Fatigue Fracture Behavior of Superalloy GH4586 at Elevated Temperature
Effects of Deformation on Surface Modification by Nitrogen Ion-Implantation
Improvement of Inner Surface for Machine Parts by Shot Peening
Oxidation Behaviour of Nickel-Based Alloys Containing High Re Contents Comparable to the Third Generation Nickel-Based Superalloys
Plasma Etching for Fabricating the Concave-Type DRAM Capacitors
Vertical Etching of Ru Electrodes Using the O2/Cl2 System
Dry Oxidation Behavior of Epitaxial Si0.7Ge0.3 Films
Crystal Growth of Aluminum Magnesium Borides from Al-Mg-B Ternary System Solutions and Properties of the Crystals
Corrosion Characteristics of Surface-Modified DET Magnesium Powders
Plasma Characteristics of Supersonic Nitrogen/Hydrogen-Mixture and Ammonia Plasma Jets and Nitrided Material Properties
Electrodeposition of Bi2Te3 for Nanowire Application
Fabrication of Si Nitride Coating onto Metal Substrate by Reactive RF Plasma Spraying
Characteristics of the Compound Layer on the SCM 435 Steel Produced by Plasma Nitrocarburizing
Material Spraying Using Electromagnetically Accelerated Plasma Jet
Electrochemical Kinetics Study of Electroless Copper Plating for Electronics Application
Property of Laser Welded Bake-Hardening Steel in Tailored Blanks for Automobile
Reaction between Sn-In Solder and Under Bump Metallurgy
A Study on Interfacial Reaction between Electroless Plated Ni-P/Au UBM and Sn-Bi Eutectic Solder Using AEM
Characteristics of CO2 Laser Welded 800MPa Grade TRIP Steel
Explosive Welding of Thin Plates Using Underwater Shock Wave for Surface Modification
Welding of AZ31B Magnesium Alloy by YAG Laser/ TIG Arc Hybrid Welding Process
Observation of Metal Flow Phenomenon of Lap Joints during Friction Stir Welding
Topics on Recent Friction Stir Welding Developments in Japan
Spectroscopic Analysis of Plasma Induced in Laser Welding of Aluminum Alloys
Welding of Aluminum and Steel by Friction Stir Diffusion Process
Friction Welding of A 6061 Aluminum Alloy and S45C Carbon Steel
Cu-Based Metallic Glass Matrix Composites with High Ductility
Scanning Electron Microscopy Observations of Fractal Pattern Formation in Al/Ge Bilayer Films
Fabrication of CdS Thin Film Pattern by CBD Method Using the Self-Assembled Monolayer
Dependence of Titanium Deposition upon Its Ionic State in Molten Salt
Deposition of Copper Thin Films on Titanium Nitride Layer Prepared by Flow Modulation CVD Technology
Development of Ultra Fine Crystalline Diamond Film and Some Applications
Microstructure and Chemical Properties of c-BN Films Prepared by ME-ARE
Preparation and Characterization of IZO Transparent Conducting Films by the Sol-Gel Method
Effect of UV Illumination on Deposition of Low-k Si-O-C(-H) Films by PECVD
Ferroelectric Characteristics of SrxBi2.4Ta2O9 Thin Films and Electrical Properties of the Pt/SrxBi2.4Ta2O9/TiO2/Si Structure
Observation of Crystallization Behavior in ITO Thin Films Prepared by RF-Magnetron Sputtering with and without External Heating
Hydrogen-Induced Degradation and Passivation of Ferroelectric SrBi2Ta2O9 Thin Films by Au Top Electrode
Oriented Growth of ZnO Thin Films on SiC Buffered Si(001) Substrates by Pulsed Laser Deposition
Epitaxial Growth of Mn-Doped ZnO Thin Films on Al2O3 (0001)
Characteristics of ZrO2/Al2O3 Bilayer Film for Gate Dielectric Applications Deposited by Atomic Layer Deposition Method
Effect of Binders on the Magnetic Behavior of P/M Processed FeSiBCuNb Alloy
Axial Pressing Method Using Pulse Magnetizing Field for the Preparation of Nd-Fe-B Sintered Magnets
Effect of Growth Condition on the Electrical and Magnetic Properties of Sputtered ZnCo2O4 Films
Alternating Magnetic Field Crystallization of Amorphous Si Films
Effects of Pre-Strain and Aging Treatment on the Mechanical Properties of 1.0wt.%Cu Containing Hot Rolled Steel Sheet
Coarsening Kinetics of B2 Precipitate Particles in an Elastically Constrained Fe-Al-Co Alloy
Microstructural Change of Cementite in Carbon Steels by Deformation
TEM Observat